ORP Set Points Explained: Typical mV Values For Pools, Cyanide Destruction, Chrome Reduction And Disinfection

In short: ORP (oxidation–reduction potential) is measured in millivolts and shows whether water is oxidising (positive mV) or reducing (negative or low mV). Typical control points are about +650 to +750 mV for swimming pool disinfection, above about +300 mV for cyanide oxidation, and about +200 to +300 mV at pH 2–3 for hexavalent chrome reduction. Always control pH first, because ORP depends strongly on it.

What Does an ORP Reading Tell You?

An ORP electrode measures the voltage between a platinum (or gold) sensing surface and a reference electrode. Oxidisers such as chlorine, ozone and hypochlorite push the reading up; reducing agents such as sodium bisulphite or metabisulphite pull it down. ORP does not tell you the exact concentration of a chemical, but it tracks the activity of the reaction — which is what actually matters for disinfection and effluent treatment. For the basics, see what is ORP.

Typical ORP Set Points by Application

ApplicationTypical ORPNotes
Swimming pool disinfection+650 to +750 mVKeep pH at 7.2–7.6 or the chlorine is far less effective
Cooling tower / drinking water disinfection+500 to +700 mVDepends on oxidiser and contact time
Cyanide oxidation (alkaline chlorination)Above about +300 mV, pH 10 or higherNever allow pH to fall — toxic gas risk
Hexavalent chrome reductionAbout +200 to +300 mV at pH 2–3ORP falls as Cr⁶⁺ is reduced to Cr³⁺
Dechlorination before ROLow positive mVProtects RO membranes from free chlorine

These are starting points only. Every plant should confirm its set point with lab tests, then fine-tune the controller.

Why pH Must Be Controlled First

ORP changes with pH. In a pool, the same chlorine dose gives a much lower ORP at pH 8 than at pH 7.2, because less of it is in the active hypochlorous acid form. In chrome and cyanide treatment, the chemistry only works inside a narrow pH window. That is why ORP systems are almost always paired with pH control — see the 7215-01 pH and ORP controller, which handles both.

How to Set Up an ORP Controller

  • Set point direction: for disinfection and cyanide oxidation, dose oxidiser when ORP falls below the set point. For chrome reduction, dose reducing agent when ORP rises above it.
  • Hysteresis: 10–30 mV usually prevents the dosing pump from chattering.
  • Dosing delay and alarm: allow time for mixing, and alarm if ORP does not recover within a set time — that usually means an empty chemical tank or failed pump.
  • 4–20 mA output: sends the reading to a PLC or SCADA. The 110-ORP controller has two limits and an isolated 4–20 mA output.

Electrode Care

ProblemLikely causeFix
Slow, sluggish responseCoated platinum surfaceClean gently; condition in fresh tap water
Reading drifts over daysReference junction cloggedClean junction or replace electrode
Erratic jumpsAir bubbles or poor earthingMount at an angle, check earthing and cable
Wrong value in check solutionAged electrodeReplace — typical life 1–2 years

Mistakes to Avoid

  1. Running ORP control without pH control.
  2. Copying a set point from another plant without lab verification.
  3. Mounting the electrode where dosing chemical hits it directly.
  4. Letting the electrode dry out during shutdowns.

Quick Checklist

  • pH controlled in the right window
  • Set point verified by lab test
  • Correct dosing direction (oxidiser or reducer)
  • Hysteresis and alarm delay set
  • Electrode checked in ORP test solution monthly

Frequently Asked Questions

What is a good ORP for a swimming pool?

Most pools are controlled at about +650 to +750 mV with pH held between 7.2 and 7.6. Check local health regulations for the exact requirement.

Can ORP tell me the chlorine concentration in ppm?

Not directly. ORP shows how strongly the water is oxidising, which depends on chlorine, pH, temperature and other substances. Use a chlorine test kit to relate the two at your site.

Why does my ORP reading respond slowly?

Usually the platinum surface is coated or the reference junction is clogged. Clean the electrode gently and, if it is more than one to two years old, replace it.

Do I need a separate pH controller with an ORP controller?

In almost every application, yes. ORP depends on pH, and both cyanide oxidation and chrome reduction only work in a defined pH range. A combined pH/ORP controller is a convenient option.

How often should an ORP electrode be checked?

Check it monthly in a standard ORP test solution and clean it when the response becomes slow.

Setting Up ORP Control?

Countronics makes pH and ORP indicators and controllers with relay limits and 4–20 mA outputs. Share your application and we will suggest set points and a suitable model.


In short: A contact tachometer touches the shaft centre or uses a wheel on a surface — good for checking RPM and line speed. A non-contact (photo) tachometer reads reflective tape from a
Contact vs Non-Contact vs Panel Tachometers: How RPM Is Measured And Which One To Choose
In short: An on-delay timer switches once after a set time; a cyclic timer repeats ON/OFF periods continuously; a sequential timer switches several outputs one after another; a programmable digital timer lets you
Industrial Timer Types Explained: On-Delay, Cyclic, Sequential And Programmable Timers
In short: Use a totalising (event) counter when you only need to know how many; use a preset counter when a relay must act at a target count — cutting, batching, stopping a
How To Choose An Industrial Digital Counter: Preset vs Totaliser, Input Sensors, Count Speed And Relay Outputs