Industrial batteries connected to a rectifier charger and resistor load bank for capacity testing

Battery Charge And Discharge Testing: How A Rectifier Charger Works, Discharging Through A Load And Measuring Capacity With An Ah Meter

In short: A battery’s capacity is the ampere-hours it can deliver before reaching its cut-off voltage. A rectifier charger converts AC mains to controlled DC and charges in constant-current then constant-voltage stages; a discharge test draws current through a resistor bank or electronic load until the voltage falls to the cut-off (e.g. 10.5 V for a 12 V lead-acid battery). Because the current is never perfectly constant, an ampere-hour meter integrates the actual current, stops the test at the cut-off and shows the true Ah delivered.

⚡ More on ampere-hour meters: Countronics AH meter range · What is an Ah meter?

Capacity, C-Rate and Cut-Off Voltage

A “100 Ah” battery is rated to deliver its capacity over a stated time — for example the C10 rating means 10 A for 10 hours. Discharging faster gives less usable capacity, so tests must use the rate the manufacturer specifies.

ChemistryNominal cell voltageTypical charge limitTypical discharge cut-off
Lead-acid (flooded / VRLA)2.0 Vabout 2.35–2.45 V/cell (14.1–14.7 V for 12 V)1.75 V/cell (10.5 V for 12 V)
Lithium-ion (NMC)3.6–3.7 V4.2 V/cellabout 2.75–3.0 V/cell
LiFePO₄3.2 V3.6–3.65 V/cellabout 2.5 V/cell
Ni-Cd1.2 Vconstant-current, terminated by time or ΔV1.0 V/cell

Always follow the battery maker’s datasheet for exact limits.

How a Rectifier Charger Works

  1. Transformer — steps mains AC down to the voltage the battery needs and isolates it from the supply.
  2. Rectifier — a bridge of diodes, or of thyristors (SCRs) in industrial chargers, converts AC to DC. With thyristors, delaying their firing angle each half-cycle reduces the output — this is how the charger regulates current and voltage.
  3. Filter — a choke and capacitors smooth the ripple.
  4. Control loop — measures battery voltage and current and adjusts the firing angle (or PWM in switch-mode chargers).

Charging Stages

StageWhat happensEnds when
Constant current (bulk)Charger holds a set current; voltage risesBattery reaches the charge voltage limit
Constant voltage (absorption)Voltage held; current tapersCurrent falls to a small value (e.g. about C/20)
Float (lead-acid)Lower voltage (about 2.25 V/cell) keeps the battery fullContinuous

In battery factories, banks of rectifiers perform the formation charge on new batteries, where the Ah delivered to each circuit is a key quality parameter.

How a Battery Is Discharged for Testing

  • Resistor bank — simple and robust, but current falls as battery voltage falls, so Ah is not simply current × time.
  • Electronic load — holds constant current or constant power for standard rate tests.
  • Real equipment — UPS or inverter loads for in-situ tests; see how to test UPS battery capacity.

The test runs until the battery voltage reaches the cut-off. The capacity is the Ah delivered up to that point.

How an Ampere-Hour Meter Helps

FunctionWhy it matters
Integrates actual current over timeGives true Ah even when a resistor load’s current drifts
Low-voltage cut-offEnds the discharge exactly at the end voltage — the 810AH stops at 10.5 V for 12 V batteries — and avoids over-discharge
Preset Ah on chargeStops charging after a set Ah input, e.g. for formation or equalising
Live current displayOperator sees the charge or discharge rate at a glance
Memory through power cutsLong tests are not lost

Worked Example

ItemValue
Battery12 V, 100 Ah at C10
TestDischarge at about 10 A through a resistor bank to 10.5 V
Actual current10.2 A at start, 9.4 A near the end
Time to 10.5 V9 h 30 min
Ah meter reading92.0 Ah
Capacity92 % of rated

Simply multiplying 10 A × 9.5 h would give 95 Ah — a 3 % error caused by the falling current. The Ah meter’s integrated reading is the correct one.

Charge Efficiency: Ah In vs Ah Out

Batteries return less charge than they take. Lead-acid typically needs about 105–120 % of the discharged Ah to be fully recharged; lithium-ion is close to 99 %. Measuring Ah in on charge and Ah out on discharge with a meter on each circuit shows the efficiency and flags ageing cells. Background: what is an ampere-hour meter and ampere-hour calculations for battery testing.

Practical Setup

  • Place the shunt in the battery’s main DC lead, sized near the maximum test current at 75 mV.
  • Measure voltage at the battery terminals, not at the load, to avoid cable-drop errors.
  • Test at the specified temperature or correct for temperature as the manufacturer advises.
  • Record Ah, time and end voltage for each battery — see ampere-hour logging.

Mistakes to Avoid

  1. Calculating capacity as nominal current × time with a resistor load.
  2. Discharging below the cut-off voltage.
  3. Measuring voltage at the load end of long cables.
  4. Testing at a different rate from the battery’s rating.

Quick Checklist

  • Rated capacity and rate known
  • Cut-off voltage set
  • Shunt sized to test current
  • Voltage sensed at battery terminals
  • Ah, time and end voltage recorded

Frequently Asked Questions

How is battery capacity tested?

The battery is discharged at its rated current to its cut-off voltage, and the ampere-hours delivered are measured. That figure is its actual capacity.

How does a battery charger rectifier work?

A transformer steps down AC, a diode or thyristor bridge converts it to DC, a filter smooths it, and a control loop regulates current and voltage.

What is the cut-off voltage for a 12 V lead-acid battery?

Typically 10.5 V (1.75 V per cell) for capacity tests at the 10-hour rate.

Why use an Ah meter instead of current × time?

Because the current changes during the test, especially with resistor loads. The Ah meter integrates the real current for an accurate capacity.

What is CC/CV charging?

Constant-current charging until the voltage limit is reached, then constant-voltage charging while the current tapers off.

Can the Ah meter stop the test automatically?

Yes. Models such as the Countronics 810AH stop at a low-voltage cut-off (10.5 V for 12 V batteries).

Setting Up Battery Testing?

Countronics ampere-hour meters are used for battery formation, charge and discharge testing, with low-voltage cut-off and memory through power cuts. Tell us the battery voltage, capacity and test current.


In short: A battery’s capacity is the ampere-hours it can deliver before reaching its cut-off voltage. A rectifier charger converts AC mains to controlled DC and charges in constant-current then constant-voltage stages; a
Battery Charge And Discharge Testing: How A Rectifier Charger Works, Discharging Through A Load And Measuring Capacity With An Ah Meter
In short: In electroplating, metal is deposited on the part in direct proportion to the electric charge passed — ampere-hours (Ah). At 100 % efficiency, 1 Ah per dm² deposits about 12.3 µm
Precision Electroplating With An Ampere-Hour Meter: How Plating Works, Faraday’s Law And Why Charge Control Beats A Timer
In short: Most thermocouple faults are wiring, not the sensor. Check in this order: right type selected in the instrument → polarity at every joint → same-type extension cable (no copper) → connections
Thermocouple Troubleshooting: Wrong Readings, Reversed Wires, Noise, Drift And Open Circuits